|
Available Design
Example
|
| Select Design |
- None
- DisplayPort SST Parallel Loopback without
PCR
- DisplayPort SST Parallel Loopback with AXIS
Video Interface
- DisplayPort RX-only
- DisplayPort TX-only
|
Select the design example to be generated.
- None: No design example is available for the
current parameter selection.
- DisplayPort SST Parallel Loopback without
PCR: This design example demonstrates parallel loopback from
DisplayPort sink to DisplayPort source without a Pixel Clock
Recovery (PCR) module when you turn on the Enable Video Input Image Port
parameter.
- DisplayPort SST Parallel Loopback with AXIS
Video Interface: This design example demonstrates parallel
loopback from DisplayPort sink to DisplayPort source with
AXIS Video interface when Enable
Active Video Data Protocols is set to
AXIS-VVP
Full.
- DisplayPort RX-only: This example design
demonstrates an RX-only design. The Enable Video Input Image
Port parameter must be disabled. The example
design software will report the RX link status.
- DisplayPort TX-only: This example design
demonstrates a TX-only design. The Enable Video Input Image
Port parameter must be disabled. The example
design software will report the TX link status. The design
will output color bars in 1080p format.
|
|
Design Example Files
|
| Simulation |
On, Off |
Turn on this option to generate the necessary
files for the simulation
testbench. |
| Synthesis |
On, Off |
Turn on this option to generate the necessary
files for
Quartus® Prime compilation
and hardware design. |
|
Generated HDL Format
|
| Generate File Format |
Verilog, VHDL |
Select your preferred HDL format for the
generated design example fileset. Note: This option only determines the format for the
generated top level IP files. All other files (e.g. example
testbenches and top level files for hardware demonstration) are
in Verilog HDL format.
|
|
Target Development
Kit
|
| Select Board |
- No Development Kit
-
Agilex™ 7
I-Series SoC Development Kit FA
-
Agilex™ 7
I-Series SoC Development Kit FB
-
Agilex™ 7
I-Series SoC Development Kit FC
- Custom Development Kit
|
Select the board for the targeted design example.
- No Development Kit: This option excludes all
hardware aspects for the design example. The IP core sets
all pin assignments to virtual pins.
-
Agilex™ 7
I-Series SoC FPGA Development Kit FA: This option
automatically sets the project's target device to the
AGIB027R31B1E1V. You may change the target device using the
Change Target
Device parameter, but
Altera®
strongly
recommends that you do not override the
target device. If you require a different device,
select the Custom Development Kit option. The IP core sets
all pin assignments according to the development kit.
-
Agilex™ 7
I-Series SoC FPGA Development Kit FB: This option
automatically sets the project's target device to the
AGIB027R31B1E1VAA. You may change the target device using
the Change Target
Device parameter, but
Altera®
strongly
recommends that you do not override the
target device. If you require a different device,
select the Custom Development Kit option. The IP core sets
all pin assignments according to the development kit.
-
Agilex™ 7
I-Series SoC FPGA Development Kit FC: This option
automatically sets the project's target device to the
AGIB027R31B1E1VB. You may change the target device using the
Change Target
Device parameter, but
Altera®
strongly
recommends that you do not override the
target device. If you require a different device,
select the Custom Development Kit option. The IP core sets
all pin assignments according to the development kit.
- Custom Development Kit: This option allows
the design example to be tested on a third-party development
kit with an
Altera®
FPGA. The project's target device will
be set using the target device of the current project. You
are required to modify the pin assignments.
|
| FMC Revision |
- Bitec Rev 8
- Parretto Rev 1
|
Choose the physical interface location for the
DisplayPort connectors:
-
Bitec Rev
8 selects the FMC card from Bitec Revision 8
to provide the DisplayPort connectors.
-
Parretto Rev
1 selects the Tentiva FMC card from
Parretto. This FMC card supports all DisplayPort rates.
|
|
Target Device
|
| Change Target Device |
On, Off |
Turn on this option and select the preferred
device variant for the development kit. |